Audi 100

1982-1990 of release




Audi 100
+ 1.1. Controls and devices
+ 2. Technical characteristics
+ 3. Engines
+ 4. Cooling system
+ 5. An exhaust system
+ 6. The power supply system
+ 7. Transmission
+ 8. A running gear
+ 9. A steering
+ 10. Brake system
- 11. A body
   11.1. Removal and installation of the forward buffer
   11.2. Removal and installation of facing of a radiator
   11.3. Removal and cowl installation
   11.4. Adjustment of a cable of the lock of a cowl
   11.5. Replacement Lochar
   11.6. A forward wing
   11.7. Replacement molding
   11.8. Replacement of a sealant of glass of a door
   11.9. A door upholstery (cars of release till December, 1987)
   11.10. Replacement of glass of a door and window lifter
   11.11. Removal and door installation
   11.12. The external handle of a door
   11.13. The door lock
   11.14. Adjustment of the lock of a door
   11.15. Removal and installation window lifter with the electric drive
   11.16. Removal and installation of an external rear-view mirror
   11.17. Replacement of a reflecting element of an external rear-view mirror
   11.18. Repair heating an element of back glass
   11.19. Removal and installation of the back buffer
   11.20. Removal and installation of a cover of a luggage space
   11.21. Removal and installation of the lock of a cover of a luggage space
   11.22. Replacement of a back decorative overlay with a niche under licence plate
   11.23. Removal and installation of the central console
   11.24. Clearing of drains (on the models equipped with the hatch)
   11.25. Removal and heater installation
+ 12. An electric equipment





11.10. Replacement of glass of a door and window lifter
THE GENERAL DATA

Fastening of the internal panel of a door

1 – a door frame;

2 – the internal panel;

3 – a cable of the handle of the lock;

4 – a bolt

Details window lifter

1 – glass;

2 – стеклоподъемник;

And – a site прилегания glasses

Adjustment has flown down

1 – the adjusting screw;

2 – directing window lifter

PERFORMANCE ORDER
1. To remove a door upholstery (subsection 11.9 see).
2. To take out from the holder draught of the internal handle of the lock of a door and to disconnect it from the handle.
3. To turn away four bolts of fastening of the internal panel of the door, located on corners. Thus it is necessary to note a thickness and position of compensatory elements for each bolt. The bolt of forward top fastening is under a rubber sealant of an external rear-view mirror.
4. To remove the internal panel of a door in gathering upwards.
5. For this purpose to remove from a directing core распорное a ring, to take out a plastic washer and a rubber lining. To lower and take out door glass.
6. In case of need to remove стеклоподъемник. To remove it it is similar to removal window lifter with the electric drive (subsection 11.15 see).
7. To insert glass from below and to fix a glass holder on a finger ползуна window lifter a lock ring, having established preliminary rubber lining and a washer.
8. Temporarily to establish the handle window lifter and to lower glass down to an emphasis.
9. To expose the bottom part directing window lifter so that a finger (1) glasses was in the middle of directing glasses.
10. To lift glass upwards against the stop.
11. To expose the bottom part directing window lifter so that glass adjoined to a sealant on all perimetre of a window and especially in a zone And.
12. If glass not densely adjoins or deforms a sealant it is necessary to adjust the screw glass position.
13. To establish from above the internal panel on a door, watching that draught of blocking of the lock was included into an aperture, and to fix it on corners four bolts, having established thus corresponding compensatory elements.
14. To connect a cable of the internal handle of the lock to the lever and to fix it in the holder.
15. To establish an internal upholstery of a door.