Audi 100

1982-1990 of release




Audi 100
+ 1.1. Controls and devices
+ 2. Technical characteristics
+ 3. Engines
+ 4. Cooling system
+ 5. An exhaust system
+ 6. The power supply system
+ 7. Transmission
+ 8. A running gear
+ 9. A steering
+ 10. Brake system
- 11. A body
   11.1. Removal and installation of the forward buffer
   11.2. Removal and installation of facing of a radiator
   11.3. Removal and cowl installation
   11.4. Adjustment of a cable of the lock of a cowl
   11.5. Replacement Lochar
   11.6. A forward wing
   11.7. Replacement molding
   11.8. Replacement of a sealant of glass of a door
   11.9. A door upholstery (cars of release till December, 1987)
   11.10. Replacement of glass of a door and window lifter
   11.11. Removal and door installation
   11.12. The external handle of a door
   11.13. The door lock
   11.14. Adjustment of the lock of a door
   11.15. Removal and installation window lifter with the electric drive
   11.16. Removal and installation of an external rear-view mirror
   11.17. Replacement of a reflecting element of an external rear-view mirror
   11.18. Repair heating an element of back glass
   11.19. Removal and installation of the back buffer
   11.20. Removal and installation of a cover of a luggage space
   11.21. Removal and installation of the lock of a cover of a luggage space
   11.22. Replacement of a back decorative overlay with a niche under licence plate
   11.23. Removal and installation of the central console
   11.24. Clearing of drains (on the models equipped with the hatch)
   11.25. Removal and heater installation
+ 12. An electric equipment





11.12. The external handle of a door
THE GENERAL DATA

The external handle of the lock of a door

1,2 – rotary Bracket;
3 – the handle;
4 – the screw;
5 – a lock ring;
6 – driving the lever;
7 – a spring;
8 – a casing;
9 – a sealing ring;
10 – the lock cylinder;
11 – a casing;
12 – a lining;
13 – the lock cylinder

Installation rotary Bracket

1 – deepening in the lock handle;

2 – bracket;

And, In – positions Bracket at installation

Removal

PERFORMANCE ORDER
Models of release till December, 1987
1. To pick up a screw-driver a forward part of a decorative overlay of the handle and to remove it.
2. To turn out the screw of fastening of the handle, located under an overlay.
3. To open a door and to take out rubber stub, located around the lock.
4. To turn out two screws of fastening of the handle.
5. To extend cautiously on itself the handle from a door, having deduced a hook in a forward part from a door aperture.
6. To disconnect draughts from the handle, having raised by means of a screw-driver the holder, and to remove the external handle of a door.
Models of release since December, 1987
7. To disconnect from the handle draught of blocking of the lock and executive draught.
8. To remove Bracket, having turned them on 65 °.
9. To turn out the screw and to remove the handle.

Dismantling (removal of the cylinder of the switch of the lock)

PERFORMANCE ORDER
1. To insert a key into the lock switch.
2. To turn out the screw of fastening and to take out the clown of the cylinder of the switch of the lock with a spring.
3. To take out the cylinder of the switch of the lock with a key.
4. To wind the cylinder изоляционной with a tape and only after that to take out from it a key. Otherwise of the cylinder will drop out сувалды.

Assemblage

PERFORMANCE ORDER
1. To insert the cylinder of the switch of the lock into the handle.
2. To establish a spring (1). For this purpose to compress it and to put on its one end a ledge (2).
3. To establish the clown on a tetrahedron against the stop. Thus to watch, that the ledge was between the spring ends.
4. To screw the fastening screw.

Installation

PERFORMANCE ORDER
Models of release till December, 1987
1. To insert a hook on a forward part of the handle into an aperture of a door and to connect to the handle of draught by means of a screw-driver. Thus a tip of direct draught to put on a metal spherical finger, and a tip of the bent draught – on a plastic spherical finger. To fix draughts holders.
2. To insert definitively external handle into a door with a lining.
3. To screw screws of fastening of the handle.
4. To establish rubber stub.
5. To establish a decorative overlay.
6. To check up handle work. The lock should open easily and reliably be locked.
Models of release since December, 1987
7. To establish the handle upside-down removals.
8. Thus to establish bracket in position In, and then to turn it in position And.
9. Deepening in the handle should enter into gearing with bracket. The ends of a spring (1) should be in the compressed condition at the left and to the right of drive the lever (2).