Audi 100

1982-1990 of release



Audi 100
+ 1.1. Controls and devices
+ 2. Technical characteristics
+ 3. Engines
+ 4. Cooling system
+ 5. An exhaust system
- 6. The power supply system
   - 6.1. The power supply system of carburettor engines
      6.1.1. Replacement of a filtering element of the air filter
      6.1.2. Removal and installation of the air filter
      6.1.3. Temperature regulator check
      6.1.4. Check of the valve of a temperature regulator
      6.1.5. Removal and installation of the fuel pump
      6.1.6. Check of pressure of forcing of the fuel pump
      6.1.7. Removal and installation of a cable of a drive of an accelerator
      6.1.8. Adjustment of a cable of a drive of an accelerator
      6.1.9. Replacement of the gauge of level of fuel
      6.1.10. Removal and installation of a fuel tank
      6.1.11. Replacement of the filter of thin clearing of fuel
      6.1.12. Removal and carburettor installation
      - 6.1.13. Dismantling and carburettor assemblage
         6.1.13.1. Dismantling and assemblage of carburettors of other models
      + 6.1.14. Carburettor Pierburg adjustments 1B3
      + 6.1.15. Carburettor Pierburg adjustments 2Е2
      + 6.1.16. Carburettor Keihin adjustments
   + 6.2. The power supply system of engines with fuel injection
   + 6.3. The power supply system of the diesel engine
+ 7. Transmission
+ 8. A running gear
+ 9. A steering
+ 10. Brake system
+ 11. A body
+ 12. An electric equipment










6.1.13. Dismantling and carburettor assemblage
THE GENERAL DATA

Carburettor details 1В3

1 – a warming element;
2 – the carburettor case;
3 – a sealing ring;
4 – the adjusting screw of quality
Mix (structure);
5 – the electromagnetic valve;
6 – экономайзер мощностных modes;
7 – the adjusting screw of quantity
Mixes;
8 – the accelerating pump;
9 – a valve saddle;
10 – a spring;
11 – a piston cuff;
12 – the piston of the accelerating pump;
13 – directing the piston;
14 – a lining;
 15 – a float axis;
16 – a float;
17 – the main fuel jet;
18 – a carburettor cover;
19 – a fuel jet эконостата;
20 – a fuel jet of idling;
21 – a pneumodrive air flaps;
22 – the needle valve;
23 – the automatic starting arrangement;
24 – a lining;
25 – a cover;
26 – a spray of the accelerating pump;
27 – a spring;
28 – the ball valve of a spray;
And – a starting backlash air flaps

PERFORMANCE ORDER
1. To disconnect the lever of a drive of the accelerating pump.
2. To turn away screws of fastening of a cover of the carburettor to the case and to uncover. To remove a lining.
3. To take out a float axis, to remove a float and to take out the needle valve.
4. To turn out the main fuel jet.
5. To turn out a fuel jet of idling and a fuel jet эконостата.
6. To remove the automatic starting arrangement, having turned away fastening bolts.
7. To take out the accelerating pump.
8. To turn out the electromagnetic valve.
9. To remove warming element.
10. To turn out a spray of the accelerating pump. To take out a spring and the ball valve.
11. To turn out the screw of adjustment of quality of a mix and the screw of adjustment of quantity of a mix.
12. To remove экономайзер мощностных modes, having turned away fastening bolts.
13. All details and carburettor knots to wash out in gasoline. In the presence of plentiful resinous adjournment on details to wash out them in acetone or solvent for nitropaints. It is forbidden to clean jets a wire, even soft not to break calibration. The washed out details and carburettor channels to blow compressed air. To replace the torn linings and sealing rings, and also the failed details.
14. To collect the carburettor upside-down.