| 1. To establish an external ring 3 (fig. Secondary shaft gearbox of type 013) the forward roller bearing of a secondary shaft see and to fix it on gearbox type 013 a pin 2, and on gearbox type 093 a bolt with internal шестигранником. |
| 2. To establish clamps 5 (fig. Carter of type 013 transmission), lock плунжеры 9 and a lock finger of 10 rods of plugs of a gear change see in case they were taken out. |
| 3. To establish in картер 12 (fig. type 013 Transmission see) transmissions a secondary shaft 39 with a plug 42 and a rod of 41 switchings of 1st and 2nd transfers. |
| 4. To establish on an axis 36 intermediate gear wheel 45 backings and запрессовать it in картер 12 transmissions. |
| 5. To establish in картер 12 transmissions a primary shaft 46, having entered into gearing of a gear wheel of primary and secondary shaft. |
| 6. To establish a plug of 43 switchings of 3rd and 4th transfers to a groove coupling the synchronizer, to insert a rod into an aperture of a plug and to fix a plug on a rod a pin 44. |
| 7. To establish all rods of plugs of a gear change in neutral position. |
| 8. To extrude the second internal ring 38 back двухрядного the conic roller bearing of a secondary shaft 39. |
| 9. To establish on a primary shaft 46 washer 15 acting as a part aside картера transmissions. |
| 10. To heat up to temperature 120 ° With and напрессовать against the stop an internal ring 16 needle bearings of 5th transfer, using thus corresponding the mandrel. |
| 11. To heat up to temperature 120 ° With and напрессовать a gear wheel of 34 5th transfers on a secondary shaft 39 against the stop. |
| 12. To establish both of some the needle bearing 17 on a primary shaft. |
| 13. To establish on a primary shaft 46 gear wheel of 18 5th transfers with the synchronizer and a plug of 20 inclusions of 5th transfer. |
| 14. To fix a plug 20 on a rod a pin 19. |
| 15. To heat up to temperature 120 ° With and to establish against the stop a nave 22 with a gear wreath. |
| 16. To extrude on a primary shaft an internal ring of the back bearing. |
| 17. To attach картер 12 transmissions to картеру 8 couplings, having established between them a lining 10 and to wrap bolts of 13 fastenings by the moment 25 Н·м (2,5 кгс·м). |
| 18. To include one of transfers and to fix a primary shaft from a procollar. |
| 19. To tighten a nut 33 at an end face of a secondary shaft the moment 100 Н·м (10,0 кгс·м) and законтрить it. |
| 20. To establish a lead 32 on a rod of a plug of switching of 1st and 2nd transfers. |
| 21. To shift back a rod of 35 switchings of a plug of 3rd and 4th transfers, having included thereby 3rd transfer. |
| 22. To insert the switch of transfers 30 in картер transmissions and to get a leg of a rod of the switch in a groove of a rod of a plug of 3rd and 4th transfers. |
| 23. To fix a pin a lead 32 on a rod of a plug of switching of 1st and 2nd transfers. |
| 24. To establish all rods of plugs of a gear change in neutral position. |
| 25. To establish a cover 6 (fig. the Cover of transmission gearbox of type 013 see) transmissions with a lining 23 (fig. type 013 Transmission see) and to wrap bolts of 28 fastenings by the moment 25 Н·м (2,5 кгс·м), preliminary having put on a carving a hermetic layer. |
| 26. To wrap a bolt 26 on the end of a primary shaft the moment 45 Н·м (4,5 кгс·м) and to establish new stub 27. |