Audi 100

1982-1990 of release




Audi 100
+ 1.1. Controls and devices
+ 2. Technical characteristics
+ 3. Engines
+ 4. Cooling system
+ 5. An exhaust system
- 6. The power supply system
   - 6.1. The power supply system of carburettor engines
      6.1.1. Replacement of a filtering element of the air filter
      6.1.2. Removal and installation of the air filter
      6.1.3. Temperature regulator check
      6.1.4. Check of the valve of a temperature regulator
      6.1.5. Removal and installation of the fuel pump
      6.1.6. Check of pressure of forcing of the fuel pump
      6.1.7. Removal and installation of a cable of a drive of an accelerator
      6.1.8. Adjustment of a cable of a drive of an accelerator
      6.1.9. Replacement of the gauge of level of fuel
      6.1.10. Removal and installation of a fuel tank
      6.1.11. Replacement of the filter of thin clearing of fuel
      6.1.12. Removal and carburettor installation
      + 6.1.13. Dismantling and carburettor assemblage
      + 6.1.14. Carburettor Pierburg adjustments 1B3
      - 6.1.15. Carburettor Pierburg adjustments 2Е2
         6.1.15.1. Adjustment of frequency of rotation of start-up of the engine
         6.1.15.2. Adjustment of starting backlashes air flaps
         6.1.15.3. Check of a pneumodrive throttle flaps the second chamber
         6.1.15.4. Adjustment приоткрытия throttle flaps the second chamber
         6.1.15.5. Adjustment of the accelerating pump
         6.1.15.6. Check of work of a pneumodrive throttle flaps the first chamber
         6.1.15.7. Idling adjustment
      + 6.1.16. Carburettor Keihin adjustments
   + 6.2. The power supply system of engines with fuel injection
   + 6.3. The power supply system of the diesel engine
+ 7. Transmission
+ 8. A running gear
+ 9. A steering
+ 10. Brake system
+ 11. A body
+ 12. An electric equipment





6.1.15.2. Adjustment of starting backlashes air flaps
PERFORMANCE ORDER
1. To uncover the starting arrangement (fig. of the Detail of the carburettor 2Е2 see).
2. To delay downwards a control lever air flap and to fix in this position.
3. To connect to a pneumodrive air flaps the vacuum gauge and the vacuum pump.
4. To create in a pneumodrive depression 100 мбар. If the pneumodrive is tight, depression should not fall more than on 5 мбар in a minute and decrease less than to 40 мбар.
5. To finish depression in a pneumodrive to 200–300 мбар.
6. To measure with the help probeов a starting backlash And (fig. of the Detail of the carburettor 1В3 see) the first step air flaps, it should be (1,8±0,15) mm. If necessary to adjust a backlash turn of the screw of adjustment of a course of a diaphragm which is located in an end face of a cover of a pneumodrive (see fig. of the Detail of the carburettor 2Е2).
7. To close заглушкой an atmospheric aperture of a pneumodrive and to create in it depression 200 мбар which should not vary during 1 mines if the drive is tight.
8. To measure probeом a starting backlash And the second step air flaps which should be (4,0±0,15) mm for the car with mechanical transmission and (3,9±0,15) mm for cars with automatic transmission.
9. If it is necessary, to adjust a backlash the screw in an end face of a rod of a pneumodrive air flaps.